How To Create A Useful Storage

Building a small storage warehouse can be done as a two week project with two people. A small warehouse measuring eight feet ten feet and eight feet high with a warehouse style roof. The front wall is eight feet high and the back wall is six feet tall. The side wall is tilted. Using texture 111 plywood provides a good sheathing material and an exterior face finishes at the same time. Since the warehouse is not heated and therefore does not have to comply with any building energy codes, you can frame harga plywood the walls with materials two-by-four inches. If you plan to heat the warehouse, use two-sixths, as this will accommodate the insulating material.

Starting with the floor because this is a small warehouse, we will use pre-cast concrete blocks for supporters. Block this pyramid with flat tops if placed on flat, flat, solid flat ground, will provide adequate support for your warehouse. Eight times ten feet can use at least six of these docks and eight will be better. One dock in every corner, a dock in the middle of a ten-foot dimension and a dock in the middle of the road on an eight-foot dimension should give a lot of support. Total eight docks.

Floor installation for light garden tools, wheelbarrows and the like can be as small as two or six inches for floor blocks. Better bet is two-by-eight inches and if you intend to keep something heavier, two-tenths is the best bet. All these floor blocks must be pressurized because they are in contact with the foundation of the concrete foundation. After the floor framing is complete, add one row of wood that is blocking in the middle of the floor. This will further increase the stiffness of the floor system and eliminate the mental.

The plywood floor should also be under pressure under the earth and will last much longer. Three ply-inch thick plywood is the minimum and again depending on what you are saving you can add a second layer. If you keep a grass tractor, the second layer will prevent floor panels from time to time. The plywood flooring should be tied with good construction adhesive beads and galvanized deck screws. Put the eight inch screws apart in the field and four inches apart on the edge of the plywood. Framing the walls should be done with the walls lying flat on the floor.

Each window or door openings should be framed as well. The wall sheath with your T111 leaves enough hanging over the bottom edge to nail it to the framing floor. With the help of a maid, stand on the wall, nail to the floor and lift it to make sure the pipe is installed in both directions.

Ceramic Tile Installation

A subfloor is basically a structural support for the floor while the underlayment is the foundation of ceramic tile fitting placed over the subfloor to provide a good basic working ceramic tile harga mdf.

It is important to know which type of subfloor you are working on, as it will help you choose the best undercoat for the tile work area to avoid breaking or failing eventually.

The most common subfloors that you will encounter are:

Subfloor Concrete

Concrete floors are one of the most common and excellent types for ceramic tile installation. It is important to check the concrete condition to make sure it is the appropriate state before tile preparation.

Clean the concrete subfloor, make sure to remove the debris or small pieces and fill all the gaps or slots shown. This floor should be smooth and parallel to the finished floor.

Subfloor pole

If your subfloor has existing tiles, you have two options to choose from before continuing your tile work.

The first option is to leave the tile as it was, but clean it and prepare it first before knocking, and the second option is to sculpt old tiles and clean the surface again.

Subfloor plywood

Always check the current subfloor condition if it’s plywood. It is usually advisable to have two layers of outer plywood but if you find a damaged area or a weak spot, consider removing it completely or putting a stronger lower layer on it like a support board to get good solid support.

To see which type of underlayment is most appropriate for your ceramic tile installation, learn more about the common types available:

Plywood

Although plywood is not the preferred choice for underlayment, this is definitely one of the most popular choices around. Always make sure you have an outer plywood when applying it as a bottom layer because the regular class will give in to moisture and eventually decay under the tiles.

Oriented Strand Board (OSB)

Very similar to plywood, OSB is quickly becoming a favorite because of the floor underlayment as it is tougher, waterproof and has no gaps between the sheets, which makes it ideal for indoor use.

Although waterproof, it is advisable to apply a thin sheet of plastic on it for water-resistant water, which is more suitable for rooms such as kitchens and bathrooms.

Backer Board

This pre-fabrication material sheet is lightweight, tough and durable for a good base flooring. Usually made of a thin layer of concrete or a combination of cement fiber, commonly used in areas that tend to get a lot of moisture.

Basics of Tile Ceramics

Ceramic rigid and fragile ceramic tile material, so sturdy is the most important part in installing this type of tile. Unless you want to see a cracked tile, loose tile or loose grout, you’ll need to select the appropriate bottom layer. Underlayment is what is called the harga mdf layer construction trade that takes place between your wood subfloor and your tiles.

You have several alternative ways to complete the powerful underlayment needed for ceramic tile installation.

Plywood – only one layer of plywood that is not stiff enough to stop floor deflection. It is necessary to cover an extra layer of exterior plywood to achieve a minimum thickness of at least 1 1/8 inch. You can (A) – Cover the plywood with cement boards (more below) or (B) Close the existing plywood with a second layer of exterior grade plywood. Under one of these, a thin mortar is installed to remove the air gap. In addition, in the bathroom, it is advisable to put a “bath pot” on your wooden subfloor. This refers to a thin rubber material that protects the tiles from floor expansion and contraction due to moisture, temperature and humidity.

Cement Backer Board – This is a prefabricated, lightweight concrete sheet used to cover wooden subfloor. It has a Portland concrete core concrete and fiberglass surfaces on both sides and is able to withstand exposure to prolonged moisture. Brand names include DUROCK, UTILICRETE, WONDERBOARD and GLASCRETE. The joints of the supporting board boards must be staggered in such a way that they do not fall directly over the wooden subfloor joints.

Mortar beds – Mud beds, or mortar beds, usually used by professional tile contractors. They are composed of a thick layer of roof that feels, then wire mesh, followed by a layer of mortar. The reason that most specialists use is that it takes a high level of skill and practice to ensure mortar beds produce a high enough surface. Another reason is the best foundation for tile floors. Okay, but why? Because the mortar bed has a built-in reinforcement against the floor deflection in the form of wire mesh. Cracked tiles and loose grout, and a longer floor.

Concrete Slab-
You can put your ceramic tile directly over the concrete slab, but all the gaps and holes need to be installed before tile installation when tied directly to the concrete. Some concrete slabs have been coated with healing compounds to help the plate without cracking. This compound should be removed prior to the installation of the tile to ensure a durable mortar bond, as it helps the concrete retain moisture and in some cases affects the adhesive. It is also important that the plates be as high as possible, especially with the larger size of tiles being used today. Cleaning the full concrete from debris and dust will also contribute to high-quality installation. In short, surface preparation is key.

One other possibility is to put the tiles on the existing floor. There are several things to consider. Is your floor solid, flat and in good condition? Is that enough stuck in the subfloor underneath to provide support? Good. Does linoleum or vinyl floor exist? Not so good. You need to throw it away or put a nice subflooring on it. (And notice the older vinyl flooring, which may contain asbestos fibers. You do not want to release this item from yourself, but cover it with some plywood subfloor or let the contractor remove it.If you are unsure If your floor has asbestos, contact the inspector Trained asbestos.) If you have ceramic tiles on the floor, you can put new tiles on them as long as the surface is flat and not too smooth. You may need surface sand to let your bonds have a better chance.

 

Cat Tree


Cats love to scratch. It’s just part of their DNA and who they are. The trick of anada gives them something to scratch besides your furniture, fortunately there is a whole world of cat trees out there that you can choose from. The cat tree is a pole covered with carpets so cats can not wait to drown their claws. If you are creative and want a weekend project, you can even build harga blockboard it yourself.

Take two pieces of plywood (2’x2 ‘) and paste both, for a heavier pad. Set aside to dry.

Cut 2×4 to make two of the same size. This piece will be part of the scratchpole of the cat tree, so you need to make sure it’s been long enough that your cat can actually reach out to scratch. For most cats, 3 ‘- 4’ pieces will be done.

Now, you will place these two sides side by side (long flat touching side), to make long and square centimeters. Use some wood glue to hold the pieces together and then use an electronic screwdriver to move the screws through the parts. You have to replace the screws that go from one side and then the other, without being in the position of three inches from the top or bottom of the post. If necessary, for harder wood, you can drill a starter hole, but make sure not to get to both sides of the wood.

Take one piece of plywood left, and put it in the 2×4 post. You need to drive two nails through plywood, one into each 2×4 setting for maximum strength.

It’s time to attach the cloth to the base and the top of the cat tree. Take one piece of cloth, wrap it around the base piece of plywood that has been glued together, pull the fabric ends around and drop it into the bottom of the plywood. When you turn it over, you must have the base covered in the fabric. Repeat with the perch.

Now you need to combine everything. Put the perch and plug face down, and center the base upside down on it. Bottom line you have to see what cat tree will look like upside down. You need to move two nails through the base and go into 2 x 4 to make one solid piece.

Turn right and lift the post with wood glue. Start at the top of the bottom by tightly wrapping the entire post with a sisal strap.

 

Particle Board for Kitchen Cabinets

Currently kitchen cabinets are made of particle board or plywood. Each of these building materials is ingrained with many features and advantages. These are used for various purposes other than kitchen cabinets.

Particle board is made of small bits, mostly see dust, which is glued to form a flat sheet. This sheet surface is further laminated with various types of materials such as laminated sheets to emit a sophisticated appearance. It is available in various thicknesses and surface coatings. It can also be found in different densities. Some of these boards are lined with excellent durable materials that can last for many years together. However, there is a lower end product that is laminated with thermofoil, vinyl and so on which only last a short time.

Most companies use this board for construction because it lowers production costs. It is considered more stable and tense than plywood. Although most people prefer to use this board for cabinet construction in the kitchen jual blockboard and other areas, it is less resistant to moisture. Cabinets and drawers made of this board tend to curl and peel when exposed to water vapor, water, heat and so on. This can be less desirable when cracked and wrapped. However, these boards are widely used to build most of the materials in homes and offices such as desks, cabinets and so on.

Plywood is another important material used to build various types of furniture. Plywood is basically made of veneer that is glued into various layers to form the sheet. It is available in various quality and thickness. Often lined with plastic sheet layered with wood grain.

Most often architects and constructors rarely use this type of wood because it tends to shrink over the passage of time. It also develops with moisture changes. For all these reasons, plywood is considered unstable because it can be curved and cracked. Lower class plywood is rarely used for cabinets and other accessories because it tends to degrade over time. However, top grade plywood is used for many purposes because it exudes a beautiful and elegant appearance.

This type of plywood is priced higher and includes many interesting features. Hardwood is used on this plywood and glued with waterproof adhesive. The plywood edge is strong and not void.

Higher grade plywood seems indestructible because it emits immense power and elegance that is quite unmatched. Easily absorb adhesives and hold fasteners accurately. In this type of construction material, layers are arranged in opposite directions that make plywood very resistant to warping. Even considered more stable than solid wood furniture. However, both particle board and plywood are widely used in various construction fields according to their characteristics and quality.

Plywood Meranti

Meranti is a trade name used in the plywood industry to designate a number of tropical species from the rainforest trees of the Shorea family. It is endemic to Southeast Asia with a majority of species harga plywood growing throughout Malaysia and Indonesia, although it can be found in parts of the Philippines and Northern India as well.

Meranti Wood Properties

The wood is similar in color and grain to Mahogany and is sometimes referred to as the Filipino Mahogany although its grain texture is rougher than the true Mahogany. Meranti is an unrelated grain, non-resin wood, so it is desirable for other tropical species such as Keruing that may have an oil core.

Use of construction

Meranti is tropical wood with a density varying from 25 to 50 lbs / cu ft. Its relatively low durability and manufacturing cost makes it ideal as a utility wood product for non-cosmetic use such as containers, flatbed trucks and van layers, RV construction, Drawer pads and side sides, etc. Because of its consistent grain and uniform color are also laminated and renamed for use in cabinets and flooring in the United States. In parts of Mexico, red and pink species are sought for cabinets and wood, where cosmetic faces are directly exposed.

Meranti is also used to build ships, where the nature of the rainforest allows it to stand well against moisture. The wood is generally certified BS1088 if it goes to the UK market, and is bound to use a kind of waterproof resin Phenol or Urea Formaldehyde (WBP).

Task Rates in the United States

According to the 2009 Harmonization Tariff Schedule in the United States, Meranti plywood is subject to an import duty of 8% unless it is from a tax-exempt country such as Indonesia.

Industry and Production

Meranti is widely sought throughout Europe, Asia and North America, but strong demand for cheaper replacement, Chinese Birch, has caused a contraction in global production volumes. As a result, hundreds of factories across Malaysia and Indonesia have been shut down. In addition, as a result of Critically Endangered Conservation status, this product is no longer produced in the Philippines and the quota has been strictly reduced in most parts of Indonesia. Meranti’s global demand is still uncertain in the world of plywood manufacture.

Plywood and Other Related Materials

The plywood consists of a thin veneer layer or a coating that is bonded under great pressure with the grain direction at right angles in each successive layer. This allows the production of large, dimensionally stable material sheets where most of the properties are equated throughout the surface with the strength of wood harga mdf parallel to the dominating grain. Depreciation and swelling is very small, about 0.18% along the grain and 0.27% above it ranges from 7-20% moisture content.

Usually an uneven amount of plaster is used to provide a balanced construction but genetically modified plywood, in which the central veneer pair pairs are aligned, are made. Plywood is very resistant to separation parallel to the grain of the face but is divided relatively easily in its thickness. Although cross laminated plywood is known from antiquity, plywood made of a thin layer and used as a substitute for solid wood is essentially a modern material that relies heavily on the development of economical moisture resistant adhesives.

Where one outer layer has better quality than another, the better-quality veneer is referred to as the face and the other as its back. Where the quality is the same, both are referred to as the face. The middle section is referred to as the core and in plywood with more than three layers that are directly lying under the face and back are referred to as cross band or cross bandeng. The boards installed in which the middle layer is replaced by particle board or wood core strips are glued side by side simultaneously only maintaining face veneer and cross bands, or more rarely face veneers only.

The most common plywoods include blockboards, where the core strips should not exceed 25 mm, and laminboard, where strips should not exceed 7 mm in width. The plywood is judged on the strength and stiffness of the facial veneer layer, the quality of the face veneer including the size and number of defects and fixes, and the suitability of the material for interior or exterior use, or immersion in water etc. Precisely Forms where it is stated differently between countries.